Methenolone Enanthate Powder Homebrew Recipe

Primo E Homebrew Recipe

Preparing an injectable solution of Methenolone Enanthate (Primobolan) from raw powder requires precise and sterile procedures. Here is a step-by-step guide to help you prepare a high-quality injectable solution.

Methenolone Enanthate, commonly known as Primobolan, is a long-acting anabolic androgenic steroid (AAS). Derived from dihydrotestosterone (DHT), it is used in medical settings and for performance enhancement in bodybuilding.

Materials Needed

• Methenolone Enanthate Powder: 10 grams
• Benzyl Alcohol (BA): 2ml (2% of total volume)
• Benzyl Benzoate (BB): 20ml (20% of total volume)
• Carrier Oil: Grapeseed oil, cottonseed oil, or MCT oil to make up the total volume of 100ml
• Beakers
• Sterile Vials
• Sterile Syringe Filters (0.22-micron filter recommended)
• Sterile Syringes and Needles
• Alcohol Pads
• Heating Plate or Water Bath
• Glass Stirring Rod or Magnetic Stirrer
• Protective Gloves and Sterile Workspace

Steps for Conversion

1. Weigh 10 grams of Methenolone Enanthate powder using a digital scale.
2. Place the measured powder into a beaker.
3. Add 2ml of Benzyl Alcohol (BA) and 20ml of Benzyl Benzoate (BB) to the beaker.
4. Stir the mixture until the Primo-E powder is completely dissolved. You can use a glass stirring rod or a magnetic stirrer. Apply gentle heat if needed to aid in the dissolving process, but avoid overheating to prevent the steroid from degrading.
5. Slowly add the carrier oil to the mixture while stirring until the total volume reaches 100ml.
6. Draw the solution into a large sterile syringe and attach a 0.22-micron sterile syringe filter. Filter the solution into a new sterile vial to remove any particles and ensure sterility.
7. Wipe the outside of the new sterile vial with an alcohol pad and transfer the filtered solution into the vial.
8. Cap the vial with a sterile cap and store it in a cool, dark place to maintain stability.

Key Tips:

1. Maintain Sterility: It is essential to maintain a sterile environment and equipment to prevent contamination.
2. Use Accurate Measurements: Precision is vital for both the effectiveness and safety of the solution.
3. Heat Control: Employ gentle heat when necessary, and avoid excessive heat to prevent degradation of the Methenolone Enanthate.

Safety Considerations:

1. Protective Gear: Always use gloves and protective clothing to avoid direct contact with the chemicals.
2. Ventilation: Work in a well-ventilated area to prevent inhaling fumes from solvents.
3. Disposal: Properly dispose of any waste materials according to local regulations for hazardous materials.

Methenolone Enanthate Powder for Sale

Methenolone Enanthate Conversion Recipes for 75, 100, 200mg/ml.

75mg/ml @ 300ml Methenolone Enanthate Recipe

• 22.5g primo enanthate powder (16.875ml)
• 15ml Benzyl Alcohol = 5%
• 45ml Benzyl Benzoate = 15%
• 223.125ml Grapeseed Oil

100mg/ml @ 40ml Primobolan Depot Recipe

• 4g methenolone enanthate powder
• 2ml Benzyl Alcohol = 5%
• 6ml Benzyl Benzoate = 15%
• 29 ml Grapeseed Oil

100mg/ml @ 250ml Primo E Recipe

• 25g primobolan enanthate powder (18.75ml)
• 5ml Benzyl Alcohol = 2%
• 50ml Benzyl Benzoate = 20%
• 176.25 ml Grapeseed Oil

200mg/ml @ 25ml Primo Enanthate Recipe

• 5g methenolone enanthate raw powder (3.75ml)
• 1.25ml Benzyl Alcohol = 5%
• 3.75ml Benzyl Benzoate = 15%
• 16.25 ml Grapeseed Oil

200mg/ml @ 50ml Methenolone Enanthate comversion Recipe

• 10g Primobolan E Powder (7.5ml)
• 1ml Benzyl Alcohol (2%)
• 7.5ml Benzyl Benzoate (15%)
• 17ml Grapeseed Oil
• 17ml Ethyl Oleate

200mg/ml @ 250ml Primobolan Depot Conversion Recipe

• 50g Methenolone E powder (37.5ml)
• 5ml Benzyl Alcohol = 2%
• 50ml Benzyl Benzoate = 20%
• 157.5 ml Grapeseed Oil

References

• Homebrew Steroids Forums
• Pharmaceutical Compounding Resources